Warrior Acrylic Paving Sealer
Back to Waterbased Sealers
Warrior Acrylic Paving Sealer is a pure acrylic, adhesion promoted coating with excellent durability and quick drying properties which gives a hard and resilient sheen finish. It has easy application and fast overcoating properties.
USES :
Warrior Acrylic Paving Sealer is ideal for use on all types of driveways, walkways, patios, paving around swimming pools and on concrete or clay interlocking paving bricks.
Due to the nature and severity of the conditions which may occur when coating these areas mentioned above, the effectiveness and life of the sealer is dependant on the preparation of the surface and application of the product.
SPECIFICATION OR RECOMMENDED PAINT SYSTEM :
The preparation for the application of this product is extremely important and therefore the following procedure must be followed.
NEW OR UN-COATED SURFACES :
a) The surface must be sound, uniform and not too smooth. It must be dry, clean and free from dust, oil and grease.
b) Acid etch the surface by washing it with a solution of spirits of salts and water (diluted 1:6). After the surface has been washed with the acid solution, hose down the acid-etched surface with sufficient water and allow it to dry for at least 24 hours.
c) Apply 1 coat of Acrylic Paving Sealer thinned 10% with water and allow to dry. (Stir the Warrior Acrylic Paving Sealer thoroughly with a flat paddle.) Apply 2 coats of the Warrior Acrylic Paving Sealer to finish allowing ± 4 hours drying time between coats.
- No traffic should be allowed onto the newly painted surface for at least 6 hours. A minimum of 48 hours should elapse before heavy traffic, including motor vehicles, should be allowed on the painted surface.
PREVIOUSLY PAINTED OR COATED SURFACES:
- The surface must be sound, uniform and not too smooth. It must be dry, clean and free from dust, oil and grease.
- Wash the surface with a solution of sugar soap and water or treat with a heavy duty degreaser. Hose down the surface with sufficient water and allow it to dry for at least 24 hours. Heavily contaminated areas may require a 2 nd application of degreasing liquid and washing to ensure a clean surface.
- Stir the Warrior Acrylic Paving Sealer thoroughly with a flat paddle. Apply 2 coats of the Warrior Acrylic Paving Sealer allowing + 4 hours drying time between coats.
- No traffic should be allowed onto the newly painted surface for at least 6 hours. A minimum of 48 hours should elapse before heavy traffic, including motor vehicles, should be allowed on the painted surface.
NB: If the previous coating is very smooth or has a wax type finish, allow a minimum of 72 hours drying time before allowing any heavy traffic onto the newly painted surface.
PROPERTIES :
APPLICATION: Brush, Roller, Spray*, Soft kitchen Broom
CLEANING SOLVENT: Water
THINNING SOLVENT: Water, normal coats do not require thinning
SPREADING RATE:
- PRIMER COAT : +3-6 m² per litre depending on surface porosity
- FINAL COAT : 6-8 m² per litre
DRYING TIMES:
- SURFACE DRY : 30 min
- HARD DRY : 4 hours
- OVERCOATING : 48 hours for heavy traffic
PACK SIZE: 5L, 20L
COLOUR RANGE: Granite, Fiesta Red, Toffee, Hot Chocolate, Red Berry, Olive Green
VISCOSITY: 85-90 KU
FLASH POINT: Non flammable
RELATIVE DENSITY + 1,1 kg per litre
GENERAL INFORMATION :
* For spray application consult our Technical Department.
a) Under no circumstances must this product be applied in the rain or if the surface is not properly dry.
b) In order to prevent colour variation, ensure that the batch numbers match or intermix non-matching batch numbers.
c) It is important that this product be thoroughly mixed with a flat paddle before use.
Contact us for the Warrior Acrylic Paving Sealer.